We have encountered this article relating to Installing A Bathtub listed below on the internet and decided it made sense to talk about it with you here.
Setting up a bathtub isn't exactly brain surgery, yet it does call for solid plumbing, carpentry, and also often, tiling skills. Replacing an old bathtub with a brand-new one is likewise a moderately hard task. If the old tub is readily accessible, the job can move immediately; if you have to open up a wall surface to eliminate the old bathtub and also position the new bath tub, the job is much harder. In either case, the task is within a house handyman's skills, although you will certainly require a helper to vacate the old bathtub and embeded in the brand-new one. Ensure you have certified yourself for the job and also are comfortable attempting it. As opposed to hiring a specialist to take over a halfway-completed project, it is far better to consider using one prior to you begin. Opportunities are you may require an expert plumber to make tube connections.
This write-up will aid you set up a new tub in your bathroom if you have actually already acquired a brand-new tub as well as don't require to change the setup of your previous supply of water pipelines.
Your tools and also material list should make up the following:
Preparing for the Installment
First of all, the sustaining frame supplied with the bathroom ought to be fitted (if called for) according to the producer's guidelines. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to ensure that if the faucet features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to avoid pressure on the bathtub.
Fit the adaptable tap ports to the bottom of both faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its final placement.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is separate the water supply. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be fairly bothersome due to the restricted gain access to that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipes. Once the supply pipes have actually been gotten rid of, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. When the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.
Installing the Bathtub
Using the two wood boards under its feet, position the bath tub in the called for placement. The wood boards are practical in uniformly spreading the weight of the tub over the area of the boards instead of focusing all the weight onto four tiny factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level and also changing the feet on the tub until the spirit level reviews degree.
To set up taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Switch on the water as well as check all joints and also brand-new pipework for leaks and also tighten them if required. Fill the tub and additionally inspect the overflow outlet and also the normal electrical outlet for leaks.
Finally, take care of the bath paneling as defined in the producer's user's manual. Tiling as well as sealing around the tub should wait till the bathtub has actually been used at the very least once as this will certainly settle it right into its final placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end offers a link to the current supply pipelines.
If you need to fit a monobloc, after that you will call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washing machines are in area between the faucet and the sink. Protect the faucet in place with the maker given backnut. Once the tap is firmly in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap ports. The previous type needs to be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bath satisfies the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to split a stiff seal, creating the water to penetrate the wall in between the bath as well as the tiling, causing complications with moisture and also feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your fixtures and fittings. They are offered in tubes and also cartridges, and also can sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched paper or soft rope. Remember to always fill up the bath tub with water prior to sealing, to allow for the motion experienced when the bathtub remains in usage. The sealer can split rather very early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were introduced to that article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from a friend on a different website. Do you know about another person who is fascinated with the subject? Please feel free to share it. Many thanks for your time. Visit us again soon.
Check It Out